Wiki-GuedeL

Cette page est en lecture seule. Vous pouvez afficher le texte source, mais ne pourrez pas le modifier. Contactez votre administrateur si vous pensez qu'il s'agit d'une erreur.
<color #22b14c>**Building Cluster of 2 nodes ProxmoxV4**</color>

This method is an adaptation of [[https://pve.proxmox.com/wiki/Proxmox_VE_4.x_Cluster]] in order to avoid having a block "Waiting of quorum..." during the "pvecm add" of the second node. \\ 
The problem occurs when the nodes don't have a multicast connection (it is the case with a non configurable cheap switch). \\
Therefore the connection must be configurated as unicast.

===== on Proxmox1: =====
  * Install of "omping" (not necessary)<code>
aptitude install omping</code>

  * config /etc/hosts as follow (replacing "proxmox1&2" by the real host name, "domain.tld" by the real domain and with their real IPs) and reboot: <code>
127.0.0.1       localhost.localdomain   localhost
192.168.2.160   proxmox1.domain.tld       proxmox1    pvelocalhost

192.168.2.150   proxmox2.domain.tld        proxmox2

# The following lines are desirable for IPv6 capable hosts
::1     localhost ip6-localhost ip6-loopback
ff02::1 ip6-allnodes
ff02::2 ip6-allrouters </code>


  * Build the cluster <code> root@proxmox1:~# pvecm create cluster-GuedeL
Corosync Cluster Engine Authentication key generator.
Gathering 1024 bits for key from /dev/urandom.
Writing corosync key to /etc/corosync/authkey.</code>

  * Have a check: /etc/corosync isn't empty any more <code>root@proxmox-miniitx:~# ls /etc/corosync/
authkey  corosync.conf</code> and nano /etc/corosync/corosync.conf and /etc/pve/corosync.conf give the same:<code>
totem {
  version: 2
  secauth: on
  cluster_name: cluster-GuedeL
  config_version: 1
  ip_version: ipv4
  interface {
    ringnumber: 0
    bindnetaddr: 192.168.2.160
  }
}

nodelist {
  node {
    ring0_addr: proxmox-miniitx
    name: proxmox-miniitx
    nodeid: 1
    quorum_votes: 1
  }
}

quorum {
  provider: corosync_votequorum
}

logging {
  to_syslog: yes
  debug: off
}

</code>
  * Configure transmission unicast (see [[https://forum.proxmox.com/threads/proxmox4-cluster-2-nodes-problem-with-quorum.25445/]]):
    * check that /etc/pve/corosync.conf is writable (see [[https://www.guedel.eu/dokuwiki/doku.php?id=Welcome:Proxmox:Cluster#Delete%20the%20cluster%20config%20of%20the%20removed%20node]]) <code>
ls -l /etc/pve </code>
    * save a copy of /etc/pve/corosync <code>
cp /etc/corosync/corosync.conf /etc/pve/corosync.conf.orig </code>
    * create a modified file <code>
cp /etc/corosync/corosync.conf /etc/pve/corosync.conf.modif 
nano /etc/pve/corosync.conf.modif </code> and add "expected_votes: 1" and "two_node: 1" into the section "quorum" and "transport: udpu" into the section "totem" in order to obtain: <code>
logging {
  debug: off
  to_syslog: yes
}

nodelist {
  node {
    name: proxmox-miniitx
    nodeid: 1
    quorum_votes: 1
    ring0_addr: proxmox-miniitx
  }

  node {
    name: proxmox-asrock
    nodeid: 2
    quorum_votes: 1
    ring0_addr: proxmox-asrock
  }

}

quorum {
  expected_votes: 1
  provider: corosync_votequorum
  two_node: 1
}

totem {
  cluster_name: cluster-GuedeL
  config_version: 2
  ip_version: ipv4
  secauth: on
  transport: udpu
  version: 2
  interface {
    bindnetaddr: 192.168.2.160
    ringnumber: 0
  }

}</code>
<note important>Don't forget to increment each time /etc/pve/corosync.conf is modified the value of "config_version" into the section "totem"</note> 
  *  
    * activate the modified file: <code>
cp /etc/pve/corosync.conf.modif /etc/pve/corosync.conf </code> and reboot.

===== on Proxmox2: =====
  * Install of "omping" (not necessary)<code>
aptitude install omping</code>

  * config /etc/hosts as follow (replacing "proxmox1&2" by the real host name, "domain.tld" by the real domain and with their real IPs) and reboot: <code>
127.0.0.1       localhost.localdomain   localhost
192.168.2.150   proxmox2.domain.tld       proxmox2    pvelocalhost

192.168.2.160   proxmox1.domain.tld        proxmox1

# The following lines are desirable for IPv6 capable hosts
::1     localhost ip6-localhost ip6-loopback
ff02::1 ip6-allnodes
ff02::2 ip6-allrouters </code>

  * add this machine to the cluster (replace by the IP of Proxmox1): <code>
pvecm add 192.168.2.160 </code>

===== Troubleshooting / general infos  =====

==== Links ====
  * proxmox cluster: [[https://pve.proxmox.com/wiki/Proxmox_VE_4.x_Cluster]]
  * Multicast (for proxmoxV3): [[https://pve.proxmox.com/wiki/Multicast_notes#Use_unicast_instead_of_multicast_.28if_all_else_fails.29]]
  * Cluster file system: [[http://pve.proxmox.com/wiki/Proxmox_Cluster_file_system_%28pmxcfs%29]]
  * Manpage of corosync: [[http://manpages.ubuntu.com/manpages/maverick/man5/corosync.conf.5.html]]


==== Configure broadcast instead of multicast ====
This method [[https://forum.proxmox.com/threads/waiting-for-quorum-in-proxmox-ve-4-0-beta-2.23551/page-2]] Post #27 didn't work by me: I had further a "waiting for quorum...".

==== Remove a node from the cluster ====
Shutdown the node to be removed and from another node staying into the cluster: <code>
pvecm delnode node_to:be_removed </code>

==== Delete the cluster config of the removed node ====
  * Delete the ssh-keys and hosts from /root/.ssh. <code>
rm /root/.ssh/* </code> works if all can be deleted.
  * Delete the key of corosync: <code>
rm /etc/corosync/authkey </code>
  * Delete /etc/pve/corosync.conf:
    * if /etc/pve/corosync is writable, simply delete it
    * if /etc/pve/corosync is not writable ([[http://pve.proxmox.com/wiki/Proxmox_Cluster_file_system_%28pmxcfs%29]]) <code>
service pve-cluster stop
pmxcfs -l
rm  /etc/pve/corosync.conf
service pve-cluster stop
service pve-cluster start   ## some errors can occur!!
service pvedaemon restart
service pveproxy restart
service pvestatd restart
restart
systemctl status pve-cluster.service     ## should be without errors now
</code>

<note>modifying or deleting /etc/corosync/corosync.conf seems to have no influence on /etc/pve/corosync.conf</note>
Wiki-GuedeL

Outils pour utilisateurs

Outils du site

Outils de la page
